Diago Little Smasher Guitar Amp Head

Diago Little Smasher Guitar Amp Head
The Diago Little Smasher combines the responsive tone and immediate simplicity of the most sought after amps; with the compact size reliability and volume control needed by todays discerning guitar player. The Diago Little Smasher is an amazingly lively and dynamic 5-Watt guitar amp head squeezed into a pedal-sized enclosure. Its ideal for small gigs studio and home use with more than enough volume to annoy the neighbours.

A fully fledged amp head its four analogue modelled cascading gain stages adjusted by Gain and Volume controls give a range of tones from chimey clean to plexi-esque rock crunch and its designed to work especially well with pedals up front if you need to push it further or want multiple channels. It also has active Bass and Treble controls with a massive 15dB boost and 30dB cut available on each. 5-Watts doesnt sound like a lot but its surprisingly loud and can drive a wide range of cabinets; anything up to a 4×12 which it does with ease – and sounds great with plenty of grunt. Its rich harmonically complex tone and road worthy reliability comes by combining the very best design components and construction methods. Features/Specifications: 5-Watt Portable Guitar Amp Head Controls – Volume | Gain | Treble | Bass Compact & portable (600g – 120 x 43 x 86mm) – pedal-sized solution that can be velcroed to your pedal board 4 to 16 Ohms output impedance – can be used with any speaker cabinet 2-band active EQ – +15dB / -30dB offers more tonal range than a 3-band passive EQ Powered on standard 9V DC @ 600mA Very tough – 2mm fabricated carbon steel construction which is durable and shock resistant Package includes – Little Smasher power supply manual Velcro and rubber foot pad. Further Specs: Type:           – Pedal-sized guitar amplifier head           – Single channel all analogue signal path with 4 analogue modelled cascading gain stages and solid state Class A/B power amplifier Output:           – 5 Watts RMS clean (before distortion)           – 4-16 Ohm output impedance – to drive any passive speaker cabinet           – DO NOT CONNECT TO ANY ACTIVE ELECTRONICS Channels: 1 Controls:           – Volume           – Gain           – Treble           – Bass           – Active EQ +15dB / -30dB Casing: 2mm fabricated carbon steel Power: 9V DC @ 600mA – power supply included Dimensions: 43(H) x 120(W) x 86mm(D) Diago Guitar-and-Bass EXL

More Information and order online::
Diago Little Smasher Guitar Amp Head

Over a million songs
and hundreds of playlists.
Listen ad-free anywhere
at anytime
Join for free now!




Diago Gigman PB02 Pedal Board

Diago Gigman PB02 Pedal Board
Diago Gigman PB02 Pedal Board Pedals Not Included

A Diago Pedal Board is the most convenient way to organise protect and transport your effects pedals. It combines a lightweight and roadworthy pedal board and hard case making it ideal for transporting your gear between home gigs and practices. It makes set-up and take-down quick and easy and is great for storing your pedals at home so that they can be neatly hidden away from your wife/mum/significant other. Undo the catches remove the lid plug in your guitar amp and power supply and youre ready to rock and roll. Easy Internal Width – 600mm Internal Depth – 300mm Internal Height – 85mm Holds Pedals – 8 – 10 Weight – 4 KG Velcro Included – 2M Diago Guitar-and-Bass 9V6

More Information and order online::
Diago Gigman PB02 Pedal Board

Diago PS06 White Adaptor

Diago PS06 White Adaptor
For use with the Diago Powerstation Pedal Board Power Supply.

The White Adaptor allows you to use the Diago Powerstation Pedal Board Power Supply to power pedals that have no external power socket but require a 9V battery. Not sure if your pedal needs this adaptor? Click here to download a PDF and check both its compatibility with the Powerstation and if an adaptor is required: Diago Guitar-and-Bass GB8

More Information and order online::
Diago PS06 White Adaptor


Diago Patchfactory Patch Cable & Plug Kit

Diago Patchfactory Patch Cable & Plug Kit
The Diago Patchfactory patch cable and plug kit gives you complete control and personality when crafting your perfect pedal board by giving you the opportunity to easily cut and fix the cables to your own desired length eliminating the common problem of short and bulky patch leads.

Features Strong and Reliable Connections Taking an innovative approach to designing the robust connections Diago have used fine metric thread on the insides of the jacks as opposed to coarse imperial thread to allow for a tight reliable hand lock system. Each cap has a sleek machine cut coin slot on the top allowing you to tighten and construct patch leads on the go without any additional tools. Simple Design Utilizing a design with no loose components what so ever the Diago Patchfactory patch cables are designed to avoid soldering and cable stripping by incorporating a simple sharp pin at the centre of the jack to make the connection with the central multi-strand wires making them extremely easy to construct. Sound Quality The Diago Patchfactory utilizes Diago UK designed cable that has a super-low capacitance of 30pF/ft (approx. 100pF/m) to prevent the treble roll-off caused by the high capacitance of poor quality cables. Thinner Cable & Compact Jack Designed with versatility in mind Diago have created the heads of the jack ports to be discrete and as compact as possible allowing small pedal boards or players with large amounts of pedals to save room and put the pedals as close together as possible. Also employing a unique design tweak that allows for the cable to be fractionally thinner the Diago Patchfactory Patch Cables give you the ability to arrange your cabling more precisely and effectively whether bending round corners or through small gaps. Specifications Kit Contains 10 x Solderless 1/4″ Angled Jack Plugs 10ft (3.5m) Patch Cable 1 x Diago Cable Cutter Diago Guitar-and-Bass 12DP

More Information and order online::
Diago Patchfactory Patch Cable & Plug Kit

Diago 5ft Cable

Diago 5ft Cable
The Diago Patchfactory 5ft Patch Cable is a high quality and clear sounding cable that when used with Diagos Patchfactory Angled Jacks gives you complete control and personality when crafting your perfect pedal board. Easy to cut fix and connect the cables to your own desired length the Diago Patchfactory eliminates the common problem of short and bulky patch leads.

Features Sound Quality The Diago Patchfactory utilizes Diago UK designed cable that has a super-low capacitance of 30pF/ft (approx. 100pF/m) to prevent the treble roll-off caused by the high capacitance of poor quality cables. Thinner Cable Also employing a unique design tweak that allows for the cable to be fractionally thinner the Diago Patchfactory Patch Cables give you the ability to arrange your cabling more precisely and effectively whether bending round corners or through small gaps. Specifications 5ft Cable Black Diago Books-DVD-and-Sheet-Music 12DS

More Information and order online::
Diago 5ft Cable

Diago PS03 Green Adaptor

Diago PS03 Green Adaptor
For use with the Diago Powerstation Pedal Board Power Supply.

The Green Adaptor allows you to use the Diago Powerstation Pedal Board Power Supply to power pedals that require a centre-positive 2.5mm barrel plug. Not sure if your pedal needs this adaptor? Click here to download a PDF and check both its compatibility with the Powerstation and if an adaptor is required: Diago Guitar-and-Bass GB5

More Information and order online::
Diago PS03 Green Adaptor

Diago Powerstation Pedal Board Power Supply

Diago Powerstation Pedal Board Power Supply
The Diago Powerstation is the ultimate pedal board power supply. It will power from 1 to 30 pedals without noise or hum.

Powering multiple effects pedals has long been a problem and there are many power supplies available at varying costs quality compatibility and performance. Most pedal power supplies are transformer type linear regulated designs which are cheap to design and develop but are expensive to make (and therefore buy) noisier bigger heavier and they get much hotter! Cheaper power supplies are usually under-rated unregulated poorly filtered designs that polute your guitars signal with splurges of noise and hum. More expensive power supplies are often engineering marvels but there really is no need and they cost far too much. The Diago Powerstation uses digital switch mode technology making it quiet light efficient and small reliably powering your pedals so you can concentrate on making music. Specifications Output: 9V DC @ 3000 mA (25W) Input: 90-264VAC @ 50-60Hz Efficiency: ~80% Line Regulation: ±0.5% max Load Regulation: ±1% max Mains Cable Inlet: 2m Figure 8 Lead IEC320-C8 Output Barrel: 2.1 x 5.5 x 12mm female barrel centre -ve Dimensions: 93mm(L) x 58mm(W) x 33mm(D) Protection: Short circuit overload and over voltage protection Operating Temperature: 0°C to +40°C Storage Temperature: -40°C to +85°C Approval: CE UL cUL TUV CB BSMI RoHS and WEEE Diago Guitar-and-Bass AEN

More Information and order online::
Diago Powerstation Pedal Board Power Supply

Diago PB08 Commuter Portable Pedalboard and Softcase

Diago PB08 Commuter Portable Pedalboard and Softcase
The Diago Commuter is a pedal board with a softcase ideal for guitarists on the go because of its portability and light weight build. As well as the sturdy pedalboard it also includes a soft carry case with straps and pedal tape.

Pedalboard The Diago Commuter features a 12mm thick HDF board with a touch satin black coating for years of use on the road. 6 rubber pads give extra stability and weight distribution for a solid sturdy feel when you stomp. The built in handle makes it easy to get out of the case and carry on stage but if you need the extra space on the board you can just Velcro right over it. Not too Big Not too Small The Commuter pedalboard is small enough to be compact and portable but large enough to hold up to 10 Boss sized effects pedals plus a Diago Powerstation or MicroPower9. Crybaby style wah pedals also fit perfectly. Check the attached PDF to see if your other pedals will fit inside. A deep zip pocket on the front of the case accommodates other accessories a phone or netbook computer. Secure Fit The Commuter has a super grip pedal carpet which will remain grippy for the lifetime of the pedalboard. Each pedalboard also comes with 2m/6″6 of self adhesive pedal tape. When the self adhesive hook tape is applied properly your pedals will never come loose. Superior Protection The rugged carry case has a dense EPE foam shell and a hard wearing 600 denier fabric cover which protects against bumps and scratches. Heavy duty zips and ABS clips keep your gear safe and secure whilst on the move and a carry handle and shoulder strap male travel easy. Diago Guitar-and-Bass WYJ

More Information and order online::
Diago PB08 Commuter Portable Pedalboard and Softcase

Diago Angled Patch Plug

Diago Angled Patch Plug
The Diago Angled Patch Cable Plug is a unique and high performance 1/4″ jack plug that can be used with the Diago PatchFactory cable to create unique pedalboard patch cables to your own specifications.

Features/Specifications Strong and Reliable Connections Taking an innovative approach to designing the robust connections Diago have used fine metric thread on the insides of the jacks as opposed to coarse imperial thread to allow for a tight reliable hand lock system. Each cap has a sleek machine cut coin slot on the top allowing you to tighten and construct patch leads on the go without any additional tools. Compact Jack Size Designed with versatility in mind Diago have created the heads of the jack ports to be discrete and as compact as possible allowing small pedal boards or players with large amounts of pedals to save room and put the pedals as close together as possible. Diago Books-DVD-and-Sheet-Music 12DR

More Information and order online::
Diago Angled Patch Plug

Diago PS04 Blue Adaptor

Diago PS04 Blue Adaptor
For use with the Diago Powerstation Pedal Board Power Supply. Your title here…

The Blue Adaptor allows you to use the Diago Powerstation Pedal Board Power Supply to power pedals that require a positive tip 3.5mm minijack plug. Not sure if your pedal needs this adaptor? Click here to download a PDF and check both its compatibility with the Powerstation and if an adaptor is required: Diago Guitar-and-Bass GB6

More Information and order online::
Diago PS04 Blue Adaptor

Diago Showman PB03 Pedal Board

Diago Showman PB03 Pedal Board
Diago Showman PB03 Pedal Board Pedals Not Included

A Diago Pedal Board is the most convenient way to organise protect and transport your effects pedals. It combines a lightweight and roadworthy pedal board and hard case making it ideal for transporting your gear between home gigs and practices. It makes set-up and take-down quick and easy and is great for storing your pedals at home so that they can be neatly hidden away from your wife/mum/significant other. Undo the catches remove the lid plug in your guitar amp and power supply and youre ready to rock and roll. Easy Internal Width – 750mm Internal Depth – 350mm Internal Height – 100mm Holds Pedals – 12 – 16 Weight – 7 KG Velcro Included – 3M Diago Guitar-and-Bass 9V7

More Information and order online::
Diago Showman PB03 Pedal Board

Diago Angled Patch Cable Plugs – Pair

Diago Angled Patch Cable Plugs – Pair
The Diago Angled Patch Cable Plugs are a pair of unique and high performance 1/4″ jack plugs that can be used with the Diago PatchFactory cable to create unique pedalboard patch cables to your own specifications.

Features/Specifications Strong and Reliable Connections Taking an innovative approach to designing the robust connections Diago have used fine metric thread on the insides of the jacks as opposed to coarse imperial thread to allow for a tight reliable hand lock system. Each cap has a sleek machine cut coin slot on the top allowing you to tighten and construct patch leads on the go without any additional tools. Compact Jack Size Designed with versatility in mind Diago have created the heads of the jack ports to be discrete and as compact as possible allowing small pedal boards or players with large amounts of pedals to save room and put the pedals as close together as possible. Diago Books-DVD-and-Sheet-Music 12DQ

More Information and order online::
Diago Angled Patch Cable Plugs – Pair

Diago Tourman PB04 Pedal Board

Diago Tourman PB04 Pedal Board
Diago Tourman PB04 Pedal Board Please note: Pedals are not included.

A Diago Pedal Board is the most convenient way to organise protect and transport your effects pedals. The Diago Tourman combines a lightweight and roadworthy pedal board and hard case making it ideal for transporting your gear between home gigs and practices. The Tourman makes set-up and take-down quick and easy and is great for storing your pedals at home so that they can be neatly and safely hidden away when not in use. Undo the catches remove the lid plug in your guitar amp and power supply and youre ready to rock and roll. It couldnt be easier! Features and Specifications Internal Width: 1020 mm Internal Depth: 450mm Internal Height: 100mm Holds Pedals: Up To 30 Weight: 10 KG Velcro Included: 4M Diago Guitar-and-Bass 9V8

More Information and order online::
Diago Tourman PB04 Pedal Board